Adjusting your sights

As a recurve archer, your sight is a vital piece of your equipment. Recently, I had a request to do a blog about the anatomy of a sight and how to adjust it. Although every sight is different, they all have similar components. We will use the Cartel Mighty sight in this example.

A recurve sight is typically made of four components; the riser mount with knob, horizontal extension bar, vertical sight bar, and scope. The riser mount is used to attach the sight to the riser and the knob is used to hold one end of the horizontal extension bar. The vertical sight bar is mounted to the other end of horizontal extension bar with the scope attached to it.  The vertical sight bar and scope have thumb screws that are used to adjust and micro-adjust the scope in relationship to the target.

Most sights have three knobs, one to adjust the length of the horizontal extension bar, one to adjust the height of the scope and one to adjust the left/right location of scope. The latter two usually have both large and micro-adjustments available. When you are ready to start adjusting your sight, remember the simple rule, “Follow the arrow”. Check out my earlier blog called Follow the Arrow: Adjust your sights.

To adjust the length of the horizontal extension bar simply loosen the knob and extend it to the desired length and tighten the knob to secure it. The marks on the bar to help you remember the length so you can set it up again.

To make an adjustment of the vertical location of the scope, loosen the thumb screw fastener and either depress the thumb lever for a large move or turn the micro-knob for small adjustment. Once complete then tighten the thumb screw fastener to secure it.

To make a left or right adjustment of the scope, loosen the thumb screw fastener and either twist the scope in or out for a large change, or twist the tension knob for micro-adjustments and then tighten the thumb screw fastener to secure it.

Once you have adjusted your sight make sure to shoot several arrows to confirm your adjustments. Once you are satisfied with the results, record the location of the sight marks on the vertical sight bar. Remember as you grow, develop muscle and change equipment your sight marks will move. One trick is to add a thin piece of white tape over the sight marks. This allows you to adjust the markings without permanently damaging the sight itself.

Drying Feathers

Now that we are in the outdoor season there is an opportunity to shoot in all kinds of weather. Weather itself effects the way we shoot, and you can read my earlier blog about different weather conditions and their effects on shooting. As competitive archers, we love our equipment. We have invested time, money, and countless hours in finding the perfect setup for us. So,once the tournament is complete we need to care for our equipment. We need to have our equipment in perfect condition for the next tournament.

Perfect shooting conditions rarely require additional maintenance, however not all tournaments are shot in ideal conditions and rain has the potential to do the most damage if not dealt with immediately since metal rusts, wood warps and fletching matte.

Once out of the weather, take the time to properly and thoroughly dry all your equipment. Using a clean dry cloth, wipe down your limbs, riser and stabilizer. Carefully dry your sight making sure not to lose your sight marks or damage your scope. If you use a spotting scope or binoculars make sure no water has damaged or fogged up the lens.

Finally, carefully dry your arrows by wiping the shafts dry. Plastic Vanes can be dried using a clean dry cloth however feather fletchings will need to be air dried so that are not squished. If your fletchings, plastic or feather, are matted, you need to open them up again and allow them to air dry by following the following guide:

How to dry your feathers

You will need: your arrows, a pot, water, and an oven/stove

• Fill a pot with water and bring to a boil
• Hold each arrow’s fletching over the steam
• Patiently wait for the fletching to start to open up. Remember the fletchings will open the rest of the way as they dry.
• Place the arrow in a clean dry spot with the points facing down until dry.
• Repeat for all your arrows and turn off the stove.

Taking the time after a rainy tournament to attend to your equipment, can save you money and grief.

Magnification: Zoom in on the Target

If you have ever competed outdoors in a field, 3D or target tournament you can understand the importance of being able to zoom in on the target to see how you are shooting. Although using a telephoto scope on your bow is not allowed in competition, you can use some after-the-shot magnification with binoculars or a spotting scope which can be extremely valuable.

For field and 3D, most archers use binoculars, since they are portable and much easier and quicker to align with the target and can be positioned quickly, which is important since you are changing targets often. The use of a spotting scope would be cumbersome to carry and setup from target to target.  Although binoculars are allowed in field and 3D tournament, range finders are usually prohibited.

For target, most archers use a spotting scope (also known as a sport telescope, fieldscope or minocular) because once setup the spotting scope does not need to be changed very often. Although you can use binoculars, the value of a spotting scope over binoculars is the magnification and the angled eye-piece which reduces the need to reposition your shooting stance to check the location of each arrow. The rules allow you to set-up a spotting scope within your shooting line space of 80cm. The challenge is making sure it is set up so it does not interfere with your or your opponent.

If you are new to outdoor competitions, consider investing in some type of magnification, since no matter how good your eyes are, the distances become farther and farther as you get older. Understanding how you are doing during each end, instead of after it can be the difference between standing on the podium or admiring it from a distance.