Bow Tuning – Basic Setup continued

Now that your bow is together we need to make sure the arrow rest is installed correctly, install a nocking point and adjust the center-shot. It is my recommendation to always install the arrow rest before installing your nocking point. So, let’s start with the arrow rest.

Installing the Arrow Rest

There are a lot of types or arrows rests available on the market. Check out my earlier blog about the various types of arrow rests. For this blog, I will be focusing on the most commonly used one for Olympics style bows, the pressure/plunger rest.

The main purpose of the arrow rest is to hold the arrow in place until the arrow is shot. A  plunger style arrow rest is designed with a support arm just long enough to hold the arrow, with a slight inward angle to the bow, and it moves out of the way with the shot.  They should also be adjusted so that the support arm does not protrude beyond the outside of the arrow. This is to minimize contact with the arrow and minimize impact on the arrow flight. Lastly the arrow rest must be positioned so the plunger/pressure button is square to the center of the arrow.

Olympic recurve bows come with a threaded hole for the plunger/pressure button and the arrow rest typically is installed and centered over the hole as the arrow rest and plunger work in conjunction with each other. Note, some risers have two holes and you should use the back one as a starting point which should be directly over the riser’s pivot point.

Pivot Point: The deepest part of the riser handle.

Alternatively, if your bow did not come with a threaded hole or you are using a traditional bow the arrow rest should be installed at the contact point of the arrow onto the rest directly above the “pivot point” of the bow. You may also want to investigate other types of arrow rests to match your style of bow.

Nock Pointing

Although some recurve archers use a tie-on nocking point, I recommend starting with a simple clamp-on type nock. Clamp-on style nocks are fairly easy to install and simply require your bow square and nocking pliers.

Nocking point: The location you attach your nock, it is usually measured 5mm (1/4”) above square from the center of the plunger and arrow rest.

Attach your bow square to the string so it is centered on the plunger ( or plunger hole) then measure up 5mm, attach a clamp-on nock, and secure it with nocking pliers. If your arrows are loose on your string, you can consider adding a nock serving for a better fit however once the nock is installed you can begin shooting.

Center-shot and the Plunger

For an Olympic archer the plunger (pressure button) is probably the best thing to attach to your bow for fine-tuning. The plunger can be adjusted to help match an archer’s release and counteract a lot of archer’s paradox. For a better understanding of arrow selection, center-shot and Archers Paradox check out my earlier blog.

To set your center-shot, set you plunger to the middle and install it in the threaded hole. Attach an arrow to the string, below the nock, and from behind the bow check to see if the tip is pointing slightly to the left (or right for left-handers).

Although adjusting the plunger WILL require a trial and error approach, it is important to set the plunger to the middle position using the screw on the end. The amount of pressure setting for your plunger will depend on the archer, the limb poundage and your form. The best approach is to start with medium pressure and adjust accordingly after shooting a couple of arrows (Typically clockwise for more pressure and counter-clockwise for less).

Your bow should be basically setup and ready for you to focus on  developing consistent form. In upcoming blogs I will dive deeper into fine-tuning your bow.

Rests

Basically an arrow rest is part of your bow setup that holds the arrow in place, ready to be shot. Allen asked…

What kind of rest would you recommend for a beginner recurve shooter? I’m a COMPLETE newbie to archery, so I blindly went with the archery shop guy’s recommendations when buying my first bow. I ended up buying a Samick Polaris that he set up with a rug rest. Is this a bad kind of rest to use? Wouldn’t the two non-index fletches hit the bow on the way out? My arrows tend to hit the target at an angle instead of perpendicular, so I wonder if the rest could be causing it.

First lets cover the various types, most people say there are four basic types of arrows however I believe there are five; shoot-thru, containment, drop-away, pressure/plunger rests and the additional shelf. The shelf is often overlooked because it is part of the bow, however you do “rest” the arrow on it.

Here is a general overview of each type.

Shoot-thru (or prong) rest : A two-pronged arrow rest with a gap between and spaced about two-thirds of the width of the arrow to create a cradle. The arrow sits on top of the prongs with one fletching pointing down between them and is usually spring-loaded to allow additional clearance for the fletchings. These rests can be tricky for beginners because the arrow can fall off with wind or bad form.  They are best for hunting and the use of a mechanical release.

Containment rest : A totally encircled or a simultaneous 3-point contact arrow rest holding the arrow completely in place until release. These are the most common choice for archery hunting, they are relatively easy to install and tune. Great for beginner hunters since the arrow will not fall off the rest.

Drop-away (or fall-away) rest : Designed to drop out of the way upon release and therefore eliminate any chance of contact with the arrow. Activated by the release of the string, the rest holds the arrow long enough to keep straight and needs to drop out of the way before the fletching reaches the rest. Since this can be very tricky to tune; it is best suited for a compound bow. It is popular for hunting with large fixed-blade broad heads and helical fletchings.

Pressure/Plunger rest: Used commonly by finger shooters (no-mechanical release), they are designed to counter-act the horizontal oscillation from release with your fingers. Standard type bows without a cut-away, typically use a simple flipper rest (a rest with an additional “flipper” that acts like a plunger to help push-back against the pressure). Bows designed with a cut-away for your center shot typically use a rest along with an adjustable plunger. A pressure rest is used on Olympic bows and can be used be any finger shooter.

Shelf: Most traditional longbows and modern recurves bows are now designed with a cut-away area in the riser which includes a shelf area. For this type of bow instead of a pressure rest you can choose to shoot off the shelf. An arrow rest is attached to the shelf of your bow and is usually installed with an arrow plate to the side. They serve as protection for the bow and arrow and act as a soft, smooth surface for the arrow to be shot from.

Selecting a rest depends on a list of things including…

• Type of bow (compound or recurve)
• Chosen application (hunting or target shooting),
• Type of release (finger or mechanical)
• Budget (cold hard cash)
• Experience (your ability to tune the rest and bow)
• Form (some rests are more forgiving)
• Tradition and historical nostalgia
• Competition division (division restrictions)
• And personal preference (bling factor)

There are a ton of rests available on the market and most bow manufacturers follow the same AMO (Archery Manufacturers Organization) standards. Therefore the drilling and tapping for the majority of bows are universal however before you purchase or upgrade make sure a selected rest will work and function with your bow.

A rug rest is a type of rest for a shelf and could be a very good selection for your shooting style if you are shooting traditional however it would not be the best selection for an Olympic archer or a compound hunter.  I am not in a position to recommend the best rest for your bow, since the bow is only as good as the alignment between the rest, release and nocking point. Obliviously, a better quality rest for your style of shooting can impact your accuracy.

To specifically address… My arrows tend to hit the target at an angle instead of perpendicular, so I wonder if the rest could be causing it.

A rest is only one small piece of the bow, and has very little to do with controlling the oscillation of the arrow. I would personally need to watch you shoot and inspect your bow to provide any valued and specific advice. There are a ton of things that can cause your arrow to impact the target on an angle. The bow may need tuning, you may be plucking the string, the arrows may be too stiff or too flexible, and a lot of other things.

Quick Insight: “Bows only perform actions as directed by you; so make sure you have good form first.”

For more information on good form check out my website page The 10 Basic Steps of Archery and to understand controlling arrow movement such as oscillation, check-out the complete Arrow – The series.

Arrows Series – Part 6: Fletching and Indexing

Now that you have cut your arrows you need to fletch them. Fletchings are found at the back of the arrow, traditionally made from bird feathers and are used to stabilize the arrow by creating a small amount of drag.

Wikipedia: Fletching (also known as a flight) is the aerodynamic stabilization of arrows or darts with materials such as feathers, each piece of which is referred to as a fletch. The word is related to the French word “fleche”, meaning “arrow,” via Old French; the ultimate root is Frankish fliukka. A fletcher is a maker of arrows.

Nowadays, there are two types of fletchings, real or synthetic feathers and plastic vanes. Some target archers have them attached to the arrow with a slight twist to increase arrow spin because a spinning projectile is more stable and helps reduce the effects of Archer’s Paradox (We will discuss Archer’s Paradox in more detail in the Part 7 of the series).

The most conventional style of indexing is a three-feather fletching where feathers or vanes are mounted to the arrow, evenly distributed around the spine of the arrow. One feather, called the “cock”, is set at a right angle to the string and pointed at the archer and the other two fletchings on the riser side are angled up and down away from the bow. This is done so the fletchings/vanes will not contact the bow when the arrow is shot. For compound archers the cock feather’s indexing depends on the type of arrow rest.

Quick Tip: Choose a different colour for the “cock” feather. It is great reminder to always point it towards you and away from the riser for proper nocking of the arrow.

Fletching an arrow is a time consuming and tedious task to do accurately by hand. In modern times, most people use a fletching jig, especially to fletch arrows with a slight twist. Check out my earlier blog about fletching jigs.

It is important to understand that once an arrow is released it starts to bend and if the arrow is not correctly indexed the feathers or vanes will make contact with the riser. This will cause the arrow to react differently than expected, distort your feathers and possibly cause damage to you or your equipment.

Arrows Series – Part 4: Spine, Flex and Stiffness

Before we discuss the topic of arrow spine, for proper safety and best performance, arrows need to match your entire bow setup. If you change draw weight, draw length, limbs, riser size, etc. this will affect you arrows. You may need to adjust the arrow length or require different arrows.

Arrow Myth:  An arrow is always straight.

Arrows SHOULD be perfectly straight when not in motion. However, when an arrow is released the force applied from the string causes the arrow shaft to be compressed against the resistant static weight of the arrow point and therefore bends.

Newton’s First Law of Motion: Every object in a state of uniform motion (rest) tends to remain in that state of motion (rest) unless an external force is applied to it.

Since the force applied is greater than the  resistance (weight of the tip), the arrow is propelled forward, and the shaft continues to flex and oscillate as it straightens itself. Arrow shafts that are either too stiff or too flexible will not fly well and will impact the accuracy of your shots or fail causing damage and/or injury. Therefore, we need to manage the flex properly so the arrow does not make any contact with the bow, or your arrow flight will be affected.

Important Tip: Arrow spine refers to the arrow shaft’s degree of stiffness (how much the arrow resists being bent) and is called spine deflection.

Basic Rule 1:  Shorter arrows act stiffer and longer arrows act more flexible.

Basic Rule 2: Powerful bows require stiffer arrows and less powerful bows require shafts that are more flexible.

Basic Rule 3: The heavier the tip equals greater the resistance, therefore the greater amount of compression.  So, a heavier tip causes the arrow to flex more and a lighter tip increase the stiffness.

According to the American Society for Testing and Materials (ASTM) the modern standards (ASTM F2031-05) an arrow’s official spine deflection is measured by hanging a 1.94 lb. weight in the center of a 28″ suspended section of the arrow shaft and is used for aluminum and carbon fiber arrows. (I believe original AMO standard has a basic guide to use for wood arrows spine determination and uses of 2 lb. and 26” section for standard measurement.) The actual distance the 1.94 lb. weight causes the shaft to sag down is the arrow’s actual spine deflection

For example, if a 1.94 lb. weight causes the center of a 28″ arrow to bend down 1/2 inch (.500″) the spine deflection would be .500″.  Stiffer arrows will bend less and more flexible arrows with bend more.

Almost every arrow manufacturer has its own numbering system and there are no universally agreed spine sizes among the various arrow manufacturers. Simply, the lower the deflection measurement equates to a stiffer arrow and higher the deflection measurement the more flexible the arrow. Manufacturers can number, size, and market their arrows anyway they want, as long as they provide the deflection data and test using the industry standard method.

Fortunately for us the engineers have already done the math for us and manufacturers provide spine selection charts. You are able to select an arrow based on your draw length and draw weight.

So when selecting arrows a good rule of thumb is that lighter draw weight, shorter draw length and/or lighter tip weight equals LESS arrow spine OR heavier draw weight, longer draw length and/or heavier tip weight equals MORE arrow spine.

Preparing to take on the World

The 2012 World Archery Indoor Championships in Las Vegas, Nevada are less than a month away, and I am equally excited and nervous. This will be my first experience at the World level and I am trilled about enjoying it with my junior recurve team mates, Virginie Chenier of Quebec and Caitlin Northey of Saskatchewan. I am sure that we will gel as a team however since we all live in various provinces we will develop our team round strategy at the hotel on practice days. Speaking of the Hotel, the South Point Hotel and Casino, where the event will be held, is located in the heart of the premiere southwest Las Vegas valley, just minutes away from the famous Las Vegas Strip. According to their website, some of their many amenities include a 16-screen Century Theatre movie complex, 64-lane bowling center and a handful of restaurants that cater to all appetites and tastes.  Their distinctive hotel features spacious rooms and suites with 42-inch plasma televisions, Point Plush mattresses and Wireless Fidelity throughout. A unique feature to this property is its Equestrian Center, which is the finest horse facility in the country. South Point also has a fabulous 400-seat showroom that features headliner entertainment and dancing to live bands on weekends. Although the hotel offers plenty to do, even for those under age of majority (21 in Nevada), I am not sure I will have a lot of time based on the posted schedule for the Championships. The practice venue will be open for both official arrival days, Friday and Saturday, and I plan to get there early on Saturday. The rest of the week looks like the following…

• Day 1 Official Practice & Team Captain Meeting
• Day 2 Qualification Rounds
• Day 3 Individual Eliminations
• Day 4 Team Eliminations
• Day 5 Individual and Team Finals

Immediately following the championships from February 10^th to 13^th is the World Archery Festival, stage 2 of the Indoor Archery World Cup. However, due to the amount of school I would have to miss, I have decided not to participate, instead I will fly home on February 10^th. I look forward to meeting so many new friends from all over the world, and participating in one of the archery world’s premier events. Until then, my focus will be on eliminating all distractions. First and foremost, finish this semester and exams the week before leaving. So rather than setting expectations to high; my goals are simple. First, focus on shooting and ignoring bells, whistles and the bright lights of Las Vegas. Then, give it my best effort each day, focusing on each shot and ignoring any mistakes. Lastly, learn and enjoy the complete experience. If all I bring back is the knowledge of what it takes to compete that the World level, I will succeed. I have been asked a couple of times now, however it is unknown at this time, if they will be streaming a live feed of the competition however results will be posted on the World Indoor website.