Bow Tuning – Basic Setup continued

Now that your bow is together we need to make sure the arrow rest is installed correctly, install a nocking point and adjust the center-shot. It is my recommendation to always install the arrow rest before installing your nocking point. So, let’s start with the arrow rest.

Installing the Arrow Rest

There are a lot of types or arrows rests available on the market. Check out my earlier blog about the various types of arrow rests. For this blog, I will be focusing on the most commonly used one for Olympics style bows, the pressure/plunger rest.

The main purpose of the arrow rest is to hold the arrow in place until the arrow is shot. A  plunger style arrow rest is designed with a support arm just long enough to hold the arrow, with a slight inward angle to the bow, and it moves out of the way with the shot.  They should also be adjusted so that the support arm does not protrude beyond the outside of the arrow. This is to minimize contact with the arrow and minimize impact on the arrow flight. Lastly the arrow rest must be positioned so the plunger/pressure button is square to the center of the arrow.

Olympic recurve bows come with a threaded hole for the plunger/pressure button and the arrow rest typically is installed and centered over the hole as the arrow rest and plunger work in conjunction with each other. Note, some risers have two holes and you should use the back one as a starting point which should be directly over the riser’s pivot point.

Pivot Point: The deepest part of the riser handle.

Alternatively, if your bow did not come with a threaded hole or you are using a traditional bow the arrow rest should be installed at the contact point of the arrow onto the rest directly above the “pivot point” of the bow. You may also want to investigate other types of arrow rests to match your style of bow.

Nock Pointing

Although some recurve archers use a tie-on nocking point, I recommend starting with a simple clamp-on type nock. Clamp-on style nocks are fairly easy to install and simply require your bow square and nocking pliers.

Nocking point: The location you attach your nock, it is usually measured 5mm (1/4”) above square from the center of the plunger and arrow rest.

Attach your bow square to the string so it is centered on the plunger ( or plunger hole) then measure up 5mm, attach a clamp-on nock, and secure it with nocking pliers. If your arrows are loose on your string, you can consider adding a nock serving for a better fit however once the nock is installed you can begin shooting.

Center-shot and the Plunger

For an Olympic archer the plunger (pressure button) is probably the best thing to attach to your bow for fine-tuning. The plunger can be adjusted to help match an archer’s release and counteract a lot of archer’s paradox. For a better understanding of arrow selection, center-shot and Archers Paradox check out my earlier blog.

To set your center-shot, set you plunger to the middle and install it in the threaded hole. Attach an arrow to the string, below the nock, and from behind the bow check to see if the tip is pointing slightly to the left (or right for left-handers).

Although adjusting the plunger WILL require a trial and error approach, it is important to set the plunger to the middle position using the screw on the end. The amount of pressure setting for your plunger will depend on the archer, the limb poundage and your form. The best approach is to start with medium pressure and adjust accordingly after shooting a couple of arrows (Typically clockwise for more pressure and counter-clockwise for less).

Your bow should be basically setup and ready for you to focus on  developing consistent form. In upcoming blogs I will dive deeper into fine-tuning your bow.

Arrows Series – Part 2: Measurements

As we start to dive deeper about arrows, my goal is to simplify the information so young archers can have a good basic understanding; it is not meant to be all in compassing or a physics lesson, remember I am still learning too. Therefore, the next step is to understand how arrows are measured and how to determine draw length.

The Archery Trade Association (ATA) formerly the Archery Manufacturers and Merchants Organization (AMO) has the following standard for measuring draw length:

AMO DRAW LENGTH STANDARD

For Manufacturers

Draw length is a specified distance, or the distance at the archer’s full draw, from the nocking point on the string to the pivot point of the bow grip (or the theoretical vertical projection of a tangency line to the pivot point parallel to the string) plus 1 3/4”. Draw length from pivot point shall be designed at DLPP (Draw Length Pivot Point) and shall be called TRUE DRAW LENGTH.

EXAMPLE: 26 1/4” DLPP plus 1 3/4” is the equivalent of 28” draw.

For Dealers and General Use

For practical reasons not requiring precise terms, draw length is the distance, at the archer’s full draw, from the nocking point on the string to the back of the bow at the arrow rest.

EXPLANATION: The standard Manufacturers is consistent with the Bow Weight Standard as related to the pivot point. The DLPP plus 1 3/4” is compatible to previous concepts of draw length. Draw length for Dealers and General Use relieves the burden of preciseness not required for general use and facilitates determining arrow length. THIS STANDARD SUPERSEDES THE PREVIOUS STANDARD.

This can be technical and confusing, however with most recurve risers, the distance of the draw length pivot point (DLPP) to the front edge of the riser is 1 ¾”. Therefore, in general terms…

Your approximate draw length is equal to the distance from your string to the front edge of the riser at full draw.

You could use a measuring tape to measure this distance however unless you have a very consistent anchor point and good form you will have varying results, since you should measure several times. Therefore, any archer who is at the point they are fining tuning arrows for high-level of performance they should consult a professional. Otherwise, I would suggest you use the following simple method to determine your draw length.

Arms Length method

Using a ruler (or other straight stick), place one end in the “V” of your neck (where your neck meets your chest ) and relaxed, reach straight out until your palms touch the ruler. At the point for your fingers is your approximate draw length. Your arrows should always be at least 1” to 2” longer than your draw length for safety reasons and young archers often need to set their arrow length little longer ( 2” to 3” ) to allow for growth.

This gives you a basic understanding of draw length and how arrows are measured, however, things get very complicated for young competitive archers who are still developing and growing in size once you add-in arrow stiffness and flex, arrow cost, type of equipment and bow weight.

It is important to understand how things are measured so you can understand why you are using the arrows you have.  I highly recommend you visit your local archery professional for assistance.