Moving Clicker Question?

Consistently using a clicker is one of the most difficult things for an archer to master, however once mastered you will love your clicker. Check out my earlier blogs about clickers and learning to shoot with a clicker.

Recently, one of my readers asked:

This is a bit late of a response, but I’ve started my clicker training and one of the things I’m having trouble with is nocking the arrow behind the clicker. I move the clicker with my fingers while nocking my arrow, but every time I do so, I move its position. 

First, there are three types of clickers…

Riser-mounted clickers
The clicker is mounted directly on the risers and is still relatively vertical about 1-2 inches beyond the pluger/ pressure button.

.

Extended Riser-mounted clickers
The clicker is still mounted to the riser however the click arm is adjusted horizontally beyond the face of the risers (1-3 inches beyond the front edge of the riser).

.

Sight-mounted Clickers
The clicker is mounted to the arm of the sight and is used for archers whose arrows are well beyond the face of the riser (2-10 inches beyond the front edge of the riser at full draw).

.

Ideally, the clicker should be positioned as vertical as possible and should extended a couple of mm beyond the bottom of the arrow. If the clicker sits on the top half of the arrow it may apply downward pressure and cause inconsistent arrow flight. So select a clicker that can be mounted as vertical as possible.

Next, I suggest you mark your riser/sight arm so you can ensure the clicker position before every use. Part of your pre-game bow assembly is to verify the clicker is in the correct position and the screws are tight secured. If you are still noticing that your clicker is still constantly moving the screws may not be providing a tight fit. Try replacing the attaching screw or add a locking or plastic washer.

I hope I have been able to answer your question and I would love to hear more from you.

Do you have any questions?
Are there any topics you would like me to cover?

Although, I will continue to write articles about my experiences, I want to hear from you. Everyone has questions, I would love to hear yours and I love answering them. I also encourage you to leave comments or share additional information on any article on my site.

Arrows Series – Part 6: Fletching and Indexing

Now that you have cut your arrows you need to fletch them. Fletchings are found at the back of the arrow, traditionally made from bird feathers and are used to stabilize the arrow by creating a small amount of drag.

Wikipedia: Fletching (also known as a flight) is the aerodynamic stabilization of arrows or darts with materials such as feathers, each piece of which is referred to as a fletch. The word is related to the French word “fleche”, meaning “arrow,” via Old French; the ultimate root is Frankish fliukka. A fletcher is a maker of arrows.

Nowadays, there are two types of fletchings, real or synthetic feathers and plastic vanes. Some target archers have them attached to the arrow with a slight twist to increase arrow spin because a spinning projectile is more stable and helps reduce the effects of Archer’s Paradox (We will discuss Archer’s Paradox in more detail in the Part 7 of the series).

The most conventional style of indexing is a three-feather fletching where feathers or vanes are mounted to the arrow, evenly distributed around the spine of the arrow. One feather, called the “cock”, is set at a right angle to the string and pointed at the archer and the other two fletchings on the riser side are angled up and down away from the bow. This is done so the fletchings/vanes will not contact the bow when the arrow is shot. For compound archers the cock feather’s indexing depends on the type of arrow rest.

Quick Tip: Choose a different colour for the “cock” feather. It is great reminder to always point it towards you and away from the riser for proper nocking of the arrow.

Fletching an arrow is a time consuming and tedious task to do accurately by hand. In modern times, most people use a fletching jig, especially to fletch arrows with a slight twist. Check out my earlier blog about fletching jigs.

It is important to understand that once an arrow is released it starts to bend and if the arrow is not correctly indexed the feathers or vanes will make contact with the riser. This will cause the arrow to react differently than expected, distort your feathers and possibly cause damage to you or your equipment.