Rests

Basically an arrow rest is part of your bow setup that holds the arrow in place, ready to be shot. Allen asked…

What kind of rest would you recommend for a beginner recurve shooter? I’m a COMPLETE newbie to archery, so I blindly went with the archery shop guy’s recommendations when buying my first bow. I ended up buying a Samick Polaris that he set up with a rug rest. Is this a bad kind of rest to use? Wouldn’t the two non-index fletches hit the bow on the way out? My arrows tend to hit the target at an angle instead of perpendicular, so I wonder if the rest could be causing it.

First lets cover the various types, most people say there are four basic types of arrows however I believe there are five; shoot-thru, containment, drop-away, pressure/plunger rests and the additional shelf. The shelf is often overlooked because it is part of the bow, however you do “rest” the arrow on it.

Here is a general overview of each type.

Shoot-thru (or prong) rest : A two-pronged arrow rest with a gap between and spaced about two-thirds of the width of the arrow to create a cradle. The arrow sits on top of the prongs with one fletching pointing down between them and is usually spring-loaded to allow additional clearance for the fletchings. These rests can be tricky for beginners because the arrow can fall off with wind or bad form.  They are best for hunting and the use of a mechanical release.

Containment rest : A totally encircled or a simultaneous 3-point contact arrow rest holding the arrow completely in place until release. These are the most common choice for archery hunting, they are relatively easy to install and tune. Great for beginner hunters since the arrow will not fall off the rest.

Drop-away (or fall-away) rest : Designed to drop out of the way upon release and therefore eliminate any chance of contact with the arrow. Activated by the release of the string, the rest holds the arrow long enough to keep straight and needs to drop out of the way before the fletching reaches the rest. Since this can be very tricky to tune; it is best suited for a compound bow. It is popular for hunting with large fixed-blade broad heads and helical fletchings.

Pressure/Plunger rest: Used commonly by finger shooters (no-mechanical release), they are designed to counter-act the horizontal oscillation from release with your fingers. Standard type bows without a cut-away, typically use a simple flipper rest (a rest with an additional “flipper” that acts like a plunger to help push-back against the pressure). Bows designed with a cut-away for your center shot typically use a rest along with an adjustable plunger. A pressure rest is used on Olympic bows and can be used be any finger shooter.

Shelf: Most traditional longbows and modern recurves bows are now designed with a cut-away area in the riser which includes a shelf area. For this type of bow instead of a pressure rest you can choose to shoot off the shelf. An arrow rest is attached to the shelf of your bow and is usually installed with an arrow plate to the side. They serve as protection for the bow and arrow and act as a soft, smooth surface for the arrow to be shot from.

Selecting a rest depends on a list of things including…

• Type of bow (compound or recurve)
• Chosen application (hunting or target shooting),
• Type of release (finger or mechanical)
• Budget (cold hard cash)
• Experience (your ability to tune the rest and bow)
• Form (some rests are more forgiving)
• Tradition and historical nostalgia
• Competition division (division restrictions)
• And personal preference (bling factor)

There are a ton of rests available on the market and most bow manufacturers follow the same AMO (Archery Manufacturers Organization) standards. Therefore the drilling and tapping for the majority of bows are universal however before you purchase or upgrade make sure a selected rest will work and function with your bow.

A rug rest is a type of rest for a shelf and could be a very good selection for your shooting style if you are shooting traditional however it would not be the best selection for an Olympic archer or a compound hunter.  I am not in a position to recommend the best rest for your bow, since the bow is only as good as the alignment between the rest, release and nocking point. Obliviously, a better quality rest for your style of shooting can impact your accuracy.

To specifically address… My arrows tend to hit the target at an angle instead of perpendicular, so I wonder if the rest could be causing it.

A rest is only one small piece of the bow, and has very little to do with controlling the oscillation of the arrow. I would personally need to watch you shoot and inspect your bow to provide any valued and specific advice. There are a ton of things that can cause your arrow to impact the target on an angle. The bow may need tuning, you may be plucking the string, the arrows may be too stiff or too flexible, and a lot of other things.

Quick Insight: “Bows only perform actions as directed by you; so make sure you have good form first.”

For more information on good form check out my website page The 10 Basic Steps of Archery and to understand controlling arrow movement such as oscillation, check-out the complete Arrow – The series.

Arrows Series – Part 4: Spine, Flex and Stiffness

Before we discuss the topic of arrow spine, for proper safety and best performance, arrows need to match your entire bow setup. If you change draw weight, draw length, limbs, riser size, etc. this will affect you arrows. You may need to adjust the arrow length or require different arrows.

Arrow Myth:  An arrow is always straight.

Arrows SHOULD be perfectly straight when not in motion. However, when an arrow is released the force applied from the string causes the arrow shaft to be compressed against the resistant static weight of the arrow point and therefore bends.

Newton’s First Law of Motion: Every object in a state of uniform motion (rest) tends to remain in that state of motion (rest) unless an external force is applied to it.

Since the force applied is greater than the  resistance (weight of the tip), the arrow is propelled forward, and the shaft continues to flex and oscillate as it straightens itself. Arrow shafts that are either too stiff or too flexible will not fly well and will impact the accuracy of your shots or fail causing damage and/or injury. Therefore, we need to manage the flex properly so the arrow does not make any contact with the bow, or your arrow flight will be affected.

Important Tip: Arrow spine refers to the arrow shaft’s degree of stiffness (how much the arrow resists being bent) and is called spine deflection.

Basic Rule 1:  Shorter arrows act stiffer and longer arrows act more flexible.

Basic Rule 2: Powerful bows require stiffer arrows and less powerful bows require shafts that are more flexible.

Basic Rule 3: The heavier the tip equals greater the resistance, therefore the greater amount of compression.  So, a heavier tip causes the arrow to flex more and a lighter tip increase the stiffness.

According to the American Society for Testing and Materials (ASTM) the modern standards (ASTM F2031-05) an arrow’s official spine deflection is measured by hanging a 1.94 lb. weight in the center of a 28″ suspended section of the arrow shaft and is used for aluminum and carbon fiber arrows. (I believe original AMO standard has a basic guide to use for wood arrows spine determination and uses of 2 lb. and 26” section for standard measurement.) The actual distance the 1.94 lb. weight causes the shaft to sag down is the arrow’s actual spine deflection

For example, if a 1.94 lb. weight causes the center of a 28″ arrow to bend down 1/2 inch (.500″) the spine deflection would be .500″.  Stiffer arrows will bend less and more flexible arrows with bend more.

Almost every arrow manufacturer has its own numbering system and there are no universally agreed spine sizes among the various arrow manufacturers. Simply, the lower the deflection measurement equates to a stiffer arrow and higher the deflection measurement the more flexible the arrow. Manufacturers can number, size, and market their arrows anyway they want, as long as they provide the deflection data and test using the industry standard method.

Fortunately for us the engineers have already done the math for us and manufacturers provide spine selection charts. You are able to select an arrow based on your draw length and draw weight.

So when selecting arrows a good rule of thumb is that lighter draw weight, shorter draw length and/or lighter tip weight equals LESS arrow spine OR heavier draw weight, longer draw length and/or heavier tip weight equals MORE arrow spine.

Arrows Series – Part 2: Measurements

As we start to dive deeper about arrows, my goal is to simplify the information so young archers can have a good basic understanding; it is not meant to be all in compassing or a physics lesson, remember I am still learning too. Therefore, the next step is to understand how arrows are measured and how to determine draw length.

The Archery Trade Association (ATA) formerly the Archery Manufacturers and Merchants Organization (AMO) has the following standard for measuring draw length:

AMO DRAW LENGTH STANDARD

For Manufacturers

Draw length is a specified distance, or the distance at the archer’s full draw, from the nocking point on the string to the pivot point of the bow grip (or the theoretical vertical projection of a tangency line to the pivot point parallel to the string) plus 1 3/4”. Draw length from pivot point shall be designed at DLPP (Draw Length Pivot Point) and shall be called TRUE DRAW LENGTH.

EXAMPLE: 26 1/4” DLPP plus 1 3/4” is the equivalent of 28” draw.

For Dealers and General Use

For practical reasons not requiring precise terms, draw length is the distance, at the archer’s full draw, from the nocking point on the string to the back of the bow at the arrow rest.

EXPLANATION: The standard Manufacturers is consistent with the Bow Weight Standard as related to the pivot point. The DLPP plus 1 3/4” is compatible to previous concepts of draw length. Draw length for Dealers and General Use relieves the burden of preciseness not required for general use and facilitates determining arrow length. THIS STANDARD SUPERSEDES THE PREVIOUS STANDARD.

This can be technical and confusing, however with most recurve risers, the distance of the draw length pivot point (DLPP) to the front edge of the riser is 1 ¾”. Therefore, in general terms…

Your approximate draw length is equal to the distance from your string to the front edge of the riser at full draw.

You could use a measuring tape to measure this distance however unless you have a very consistent anchor point and good form you will have varying results, since you should measure several times. Therefore, any archer who is at the point they are fining tuning arrows for high-level of performance they should consult a professional. Otherwise, I would suggest you use the following simple method to determine your draw length.

Arms Length method

Using a ruler (or other straight stick), place one end in the “V” of your neck (where your neck meets your chest ) and relaxed, reach straight out until your palms touch the ruler. At the point for your fingers is your approximate draw length. Your arrows should always be at least 1” to 2” longer than your draw length for safety reasons and young archers often need to set their arrow length little longer ( 2” to 3” ) to allow for growth.

This gives you a basic understanding of draw length and how arrows are measured, however, things get very complicated for young competitive archers who are still developing and growing in size once you add-in arrow stiffness and flex, arrow cost, type of equipment and bow weight.

It is important to understand how things are measured so you can understand why you are using the arrows you have.  I highly recommend you visit your local archery professional for assistance.

2012 Midas Riser

Late in 2010, I switched to the Cartel Midas riser and I have been extremely happy with it ever since. In fact, I switched just 6 weeks before winning my spot to the Canada Winter Games. It also was my primary bow for the World Indoor Archery Championship in Las Vegas. As part of the being on Team Canada, I was required to have a duplicate bow for international competitions. So my sponsor, Cartel Doosung sent me the new version for 2012.  Personally, once the indoor season is complete, I will be switching to the new 2012 Midas version as my primary bow.

Like Guy Fieri from Diners, Drive-ins and Dives says “It’s Money” …

The new Cartel 2012 Midas Riser is being produced in cooperation with BowKorea, one of the bright new specialist manufacturers on the highly competitive Korean archery scene. The new 2012 model is available in both 23” and 25” version for both left-handed and right-handed archers and is machined out of AL7001 CNC aluminum. It weighs only 1.14kg for 23” or 1.2 kg for 25” version, and along with the original black, blue, red and silver they have added white and green. Constructed with holes throughout the body for the windiest days and maintains the natural wood handle.

Along with the dual options for your cushion plunger, this year’s model includes a highly detailed clicker extension and the innovative side-to-side adjustable limb pocket system. So now, not only can you adjust the tiller, the new limb pocket system allows you to adjust the actual limb pocket for adaptability to a wide variety of international limb fittings (ILF) limbs.

If you are considering a new riser, check out the new 2012 Cartel Doosung Midas.