Shooting with a Clicker

Every competitive Olympic recurve archer uses a draw length checker or “clicker”. A clicker is a device that assists an archer to draw their bow consistently.  The clicker rides along the side of the arrow and produces a “clicking” sound after it passes over the point, hence the name “clicker”. By consistently measuring the draw length of the arrow, you get a consistent power off the bow and therefore a more consistent grouping of arrows resulting in better scores.

There is a lot of debate of when you should start to use a clicker. Anyone who wants to advance and develop smaller groups should start using a clicker as soon as possible. HOWEVER, since clickers take a lot of discipline, patience and practice, maturity is the key factor; age maturity and shooting maturity. If you are disciplined and maintaining consistent form, then you are ready for a clicker.

Recently, one of my readers asked:

I just wanted to ask, with regards to the form, if I should be expanding my chest during the draw (pulling your shoulders back towards the spine) in order to activate the back muscles to take the load rather than the arms.

Shooting a clicker is a relatively simple process however; it requires the use of back muscles to create something called back tension. By compressing the rhomboid major muscles (between the shoulder blades and spine) together, it will draw the arrow past the clicker for the shot when you are at full draw.

First, you need to determine the ideal location for your clicker. Have a friend mark where the tip of the arrow is at full draw. This will be the initial starting location for your clicker. There are tons of clickers on the market however there are two basic types of clickers; riser-mounted or sight-mounted. Depending where the initial starting location is measured it will help you determine the type you need.

Once you have mounted your clicker follow this shot process.

1. Nock the arrow, with the arrow under the clicker and on the arrow rest.
2. Raise the bow and draw towards your anchor point.
3. Continue to draw the arrow until the tip of the point is still just in contact with the clicker.
4. Aim and while still maintaining, squeeze your rhomboid major muscles together.
5. Once you hear the “click”, relax your fingers and finish the shot.

It is important that you are able to reach your anchor point at full draw. The clicker needs to be within the distance so your rhomboid major muscles can activate the shot. Remember, over the course of an entire day of shooting, your muscles weaken and you will have to work harder to draw the same amount, it may need to be adjusted to find the ideal location for entire day of shooting.

Important: Once you have determined your clicker location, leave it alone. Making any adjustments will affect all your sight marks, and they will need to be adjusted too.

If you have never used your rhomboid major muscles before this is going to take some time to master. Practice using your rhomboid major muscles with the following exercise.

With palms down and your forearms parallel to the floor, bring your fingertips together at chin level. Try squeezing your rhomboid major muscles together. You should witness your fingers spread apart about an inch. This is all the space you need to activate the clicker at full draw.

You can also check out this website for exercises to help develop strength in your rhomboid muscles.

The mastery of a clicker is essential for any competition archer. You will need to work on it regularly however once you master the process a clicker will become your best friend.

Adjusting your sights

As a recurve archer, your sight is a vital piece of your equipment. Recently, I had a request to do a blog about the anatomy of a sight and how to adjust it. Although every sight is different, they all have similar components. We will use the Cartel Mighty sight in this example.

A recurve sight is typically made of four components; the riser mount with knob, horizontal extension bar, vertical sight bar, and scope. The riser mount is used to attach the sight to the riser and the knob is used to hold one end of the horizontal extension bar. The vertical sight bar is mounted to the other end of horizontal extension bar with the scope attached to it.  The vertical sight bar and scope have thumb screws that are used to adjust and micro-adjust the scope in relationship to the target.

Most sights have three knobs, one to adjust the length of the horizontal extension bar, one to adjust the height of the scope and one to adjust the left/right location of scope. The latter two usually have both large and micro-adjustments available. When you are ready to start adjusting your sight, remember the simple rule, “Follow the arrow”. Check out my earlier blog called Follow the Arrow: Adjust your sights.

To adjust the length of the horizontal extension bar simply loosen the knob and extend it to the desired length and tighten the knob to secure it. The marks on the bar to help you remember the length so you can set it up again.

To make an adjustment of the vertical location of the scope, loosen the thumb screw fastener and either depress the thumb lever for a large move or turn the micro-knob for small adjustment. Once complete then tighten the thumb screw fastener to secure it.

To make a left or right adjustment of the scope, loosen the thumb screw fastener and either twist the scope in or out for a large change, or twist the tension knob for micro-adjustments and then tighten the thumb screw fastener to secure it.

Once you have adjusted your sight make sure to shoot several arrows to confirm your adjustments. Once you are satisfied with the results, record the location of the sight marks on the vertical sight bar. Remember as you grow, develop muscle and change equipment your sight marks will move. One trick is to add a thin piece of white tape over the sight marks. This allows you to adjust the markings without permanently damaging the sight itself.