Rests

Basically an arrow rest is part of your bow setup that holds the arrow in place, ready to be shot. Allen asked…

What kind of rest would you recommend for a beginner recurve shooter? I’m a COMPLETE newbie to archery, so I blindly went with the archery shop guy’s recommendations when buying my first bow. I ended up buying a Samick Polaris that he set up with a rug rest. Is this a bad kind of rest to use? Wouldn’t the two non-index fletches hit the bow on the way out? My arrows tend to hit the target at an angle instead of perpendicular, so I wonder if the rest could be causing it.

First lets cover the various types, most people say there are four basic types of arrows however I believe there are five; shoot-thru, containment, drop-away, pressure/plunger rests and the additional shelf. The shelf is often overlooked because it is part of the bow, however you do “rest” the arrow on it.

Here is a general overview of each type.

Shoot-thru (or prong) rest : A two-pronged arrow rest with a gap between and spaced about two-thirds of the width of the arrow to create a cradle. The arrow sits on top of the prongs with one fletching pointing down between them and is usually spring-loaded to allow additional clearance for the fletchings. These rests can be tricky for beginners because the arrow can fall off with wind or bad form.  They are best for hunting and the use of a mechanical release.

Containment rest : A totally encircled or a simultaneous 3-point contact arrow rest holding the arrow completely in place until release. These are the most common choice for archery hunting, they are relatively easy to install and tune. Great for beginner hunters since the arrow will not fall off the rest.

Drop-away (or fall-away) rest : Designed to drop out of the way upon release and therefore eliminate any chance of contact with the arrow. Activated by the release of the string, the rest holds the arrow long enough to keep straight and needs to drop out of the way before the fletching reaches the rest. Since this can be very tricky to tune; it is best suited for a compound bow. It is popular for hunting with large fixed-blade broad heads and helical fletchings.

Pressure/Plunger rest: Used commonly by finger shooters (no-mechanical release), they are designed to counter-act the horizontal oscillation from release with your fingers. Standard type bows without a cut-away, typically use a simple flipper rest (a rest with an additional “flipper” that acts like a plunger to help push-back against the pressure). Bows designed with a cut-away for your center shot typically use a rest along with an adjustable plunger. A pressure rest is used on Olympic bows and can be used be any finger shooter.

Shelf: Most traditional longbows and modern recurves bows are now designed with a cut-away area in the riser which includes a shelf area. For this type of bow instead of a pressure rest you can choose to shoot off the shelf. An arrow rest is attached to the shelf of your bow and is usually installed with an arrow plate to the side. They serve as protection for the bow and arrow and act as a soft, smooth surface for the arrow to be shot from.

Selecting a rest depends on a list of things including…

• Type of bow (compound or recurve)
• Chosen application (hunting or target shooting),
• Type of release (finger or mechanical)
• Budget (cold hard cash)
• Experience (your ability to tune the rest and bow)
• Form (some rests are more forgiving)
• Tradition and historical nostalgia
• Competition division (division restrictions)
• And personal preference (bling factor)

There are a ton of rests available on the market and most bow manufacturers follow the same AMO (Archery Manufacturers Organization) standards. Therefore the drilling and tapping for the majority of bows are universal however before you purchase or upgrade make sure a selected rest will work and function with your bow.

A rug rest is a type of rest for a shelf and could be a very good selection for your shooting style if you are shooting traditional however it would not be the best selection for an Olympic archer or a compound hunter.  I am not in a position to recommend the best rest for your bow, since the bow is only as good as the alignment between the rest, release and nocking point. Obliviously, a better quality rest for your style of shooting can impact your accuracy.

To specifically address… My arrows tend to hit the target at an angle instead of perpendicular, so I wonder if the rest could be causing it.

A rest is only one small piece of the bow, and has very little to do with controlling the oscillation of the arrow. I would personally need to watch you shoot and inspect your bow to provide any valued and specific advice. There are a ton of things that can cause your arrow to impact the target on an angle. The bow may need tuning, you may be plucking the string, the arrows may be too stiff or too flexible, and a lot of other things.

Quick Insight: “Bows only perform actions as directed by you; so make sure you have good form first.”

For more information on good form check out my website page The 10 Basic Steps of Archery and to understand controlling arrow movement such as oscillation, check-out the complete Arrow – The series.

Arrows Series – Part 6: Fletching and Indexing

Now that you have cut your arrows you need to fletch them. Fletchings are found at the back of the arrow, traditionally made from bird feathers and are used to stabilize the arrow by creating a small amount of drag.

Wikipedia: Fletching (also known as a flight) is the aerodynamic stabilization of arrows or darts with materials such as feathers, each piece of which is referred to as a fletch. The word is related to the French word “fleche”, meaning “arrow,” via Old French; the ultimate root is Frankish fliukka. A fletcher is a maker of arrows.

Nowadays, there are two types of fletchings, real or synthetic feathers and plastic vanes. Some target archers have them attached to the arrow with a slight twist to increase arrow spin because a spinning projectile is more stable and helps reduce the effects of Archer’s Paradox (We will discuss Archer’s Paradox in more detail in the Part 7 of the series).

The most conventional style of indexing is a three-feather fletching where feathers or vanes are mounted to the arrow, evenly distributed around the spine of the arrow. One feather, called the “cock”, is set at a right angle to the string and pointed at the archer and the other two fletchings on the riser side are angled up and down away from the bow. This is done so the fletchings/vanes will not contact the bow when the arrow is shot. For compound archers the cock feather’s indexing depends on the type of arrow rest.

Quick Tip: Choose a different colour for the “cock” feather. It is great reminder to always point it towards you and away from the riser for proper nocking of the arrow.

Fletching an arrow is a time consuming and tedious task to do accurately by hand. In modern times, most people use a fletching jig, especially to fletch arrows with a slight twist. Check out my earlier blog about fletching jigs.

It is important to understand that once an arrow is released it starts to bend and if the arrow is not correctly indexed the feathers or vanes will make contact with the riser. This will cause the arrow to react differently than expected, distort your feathers and possibly cause damage to you or your equipment.

Arrows – The Series (This time, it’s personal)

Since arrows are extremely important for an archer, I thought I would do a couple of blogs about arrows starting with the various components. I will be focusing on arrows for recurve target archers, since there are a lot of articles about arrows for both compound and traditional archery already. Selecting the correct arrows for your best performance is not simple task. There are tons of things to know and understand and it may require some trial and error. In this first blog we will start with the basic components.

An arrow is comprised of four major components the shaft, the point, the nock and the fletching.

Shaft : The shaft is primary structural component of the arrow and all other components are attached to it. Originally arrows shafts were made from wood however new shafts are made from aluminum, carbon fibre or both.  It is very important to properly match the arrow stiffness (or spine) to the archer for the best groups. Spine, or stiffness of the arrow, references how much or little the shaft bends when compressed through the shot and it typically matched by using the archer’s draw length and the bow poundage.

Fletching : Glued towards the back of the arrow, fletching are the airfoils for the arrows designed to stabilize the arrow in flight. Traditionally made from real feathers, target arrow fletching are now typically either plastic feathers or plastic vanes. Most target arrows have three fletches that are attached with a slight twist to help the arrow spin and stabilize faster in the air.  The quicker and more stabile the arrows is, the more consistent your groups will be.

Point : The point, or arrowhead, is the functional part of the arrow that is inserted and glued to the front end. It provides the weight and is typically made of various types of metal include tungsten.  Target points are usually bullet-shaped and designed to penetrate target butts easily without large amounts of damage.

.

Nock : Found at the rear end of the arrow, target nocks are typically made of plastic. They are inserted, capped over or combined with separate medal pins inserts and held in place by friction. Target nocks are designed to gently pinch the bowstring to hold it in place when the bow string is drawn.

.

Over the next few blogs we will dive deeper about these components, various discussion concepts like center shot, arrow indexing and numbering your arrows in upcoming posts and help understanding things like spine and Archer’s Paradox.

Remember, this blog is not meant cover everything about arrows. I am still learning and visit my coach regularly to help me develop my understanding about everything archery. I encourage you to share your knowledge and experiences so we can all develop together.

Remember Cartel Doosung offer a wide variety of arrow lines including aluminum and carbon fiber including their new line of Arista arrows for young archers. If you are in the market for some new arrows check my earlier blog about selecting and purchasing arrows.

Drying Feathers

Now that we are in the outdoor season there is an opportunity to shoot in all kinds of weather. Weather itself effects the way we shoot, and you can read my earlier blog about different weather conditions and their effects on shooting. As competitive archers, we love our equipment. We have invested time, money, and countless hours in finding the perfect setup for us. So,once the tournament is complete we need to care for our equipment. We need to have our equipment in perfect condition for the next tournament.

Perfect shooting conditions rarely require additional maintenance, however not all tournaments are shot in ideal conditions and rain has the potential to do the most damage if not dealt with immediately since metal rusts, wood warps and fletching matte.

Once out of the weather, take the time to properly and thoroughly dry all your equipment. Using a clean dry cloth, wipe down your limbs, riser and stabilizer. Carefully dry your sight making sure not to lose your sight marks or damage your scope. If you use a spotting scope or binoculars make sure no water has damaged or fogged up the lens.

Finally, carefully dry your arrows by wiping the shafts dry. Plastic Vanes can be dried using a clean dry cloth however feather fletchings will need to be air dried so that are not squished. If your fletchings, plastic or feather, are matted, you need to open them up again and allow them to air dry by following the following guide:

How to dry your feathers

You will need: your arrows, a pot, water, and an oven/stove

• Fill a pot with water and bring to a boil
• Hold each arrow’s fletching over the steam
• Patiently wait for the fletching to start to open up. Remember the fletchings will open the rest of the way as they dry.
• Place the arrow in a clean dry spot with the points facing down until dry.
• Repeat for all your arrows and turn off the stove.

Taking the time after a rainy tournament to attend to your equipment, can save you money and grief.

Fletchings Jig

Fletchings are found at the back of the arrow, traditionally made from bird feathers, are used to stabilize the arrow by creating a small amount of drag.   Nowadays, there are two types of fletchings, real or synthetic feathers and plastic vanes. Some target archers have them attached to the arrow with a slight twist to increase arrow spin because a spinning projectile is more stable.

Most archers start using arrows with feathers, as they are ideal at short distances; however, feathers produce a lot of drag at greater distances causing the arrow to drop a lot. Plastic fletchings called vanes produce less drag over greater distances reducing the amount of drop allowing archers to reach longer distances more consistently.

Historically, people known as “fletchers” made arrows, however fletching an arrow is a time consuming and tedious task to do accurately by hand. In modern times, most people use a fletching jig, especially to fletch arrows with a slight twist.

Fletching jigs have existed for feathers for quite a long time and more recently fletching jigs for plastic vanes have been introduced to the market. Using a fletching jig ensures the fletching feathers or vanes are evenly spaced around the arrow and consistently attached to the arrow at the same location on the arrow.

A popular target archer fletching is the plastic spin-wing vanes manufactured by range-o-matic. These vanes are light and forgiving however they can be a challenge to consistently fletch a quiver of arrows. Some archers apply spin-wings by-hand while others archers use arrow wraps that provide a guide to attaching the spin vanes correctly. Cartel Doosung offers a new spin-vane fletching jig that can help fletch spin-wing vanes consistently and evenly spaced. If you have a large number of arrows to fletch, you may want to consider a spin-vane fletching jig.