Moving Clicker Question?

Consistently using a clicker is one of the most difficult things for an archer to master, however once mastered you will love your clicker. Check out my earlier blogs about clickers and learning to shoot with a clicker.

Recently, one of my readers asked:

This is a bit late of a response, but I’ve started my clicker training and one of the things I’m having trouble with is nocking the arrow behind the clicker. I move the clicker with my fingers while nocking my arrow, but every time I do so, I move its position. 

First, there are three types of clickers…

Riser-mounted clickers
The clicker is mounted directly on the risers and is still relatively vertical about 1-2 inches beyond the pluger/ pressure button.

.

Extended Riser-mounted clickers
The clicker is still mounted to the riser however the click arm is adjusted horizontally beyond the face of the risers (1-3 inches beyond the front edge of the riser).

.

Sight-mounted Clickers
The clicker is mounted to the arm of the sight and is used for archers whose arrows are well beyond the face of the riser (2-10 inches beyond the front edge of the riser at full draw).

.

Ideally, the clicker should be positioned as vertical as possible and should extended a couple of mm beyond the bottom of the arrow. If the clicker sits on the top half of the arrow it may apply downward pressure and cause inconsistent arrow flight. So select a clicker that can be mounted as vertical as possible.

Next, I suggest you mark your riser/sight arm so you can ensure the clicker position before every use. Part of your pre-game bow assembly is to verify the clicker is in the correct position and the screws are tight secured. If you are still noticing that your clicker is still constantly moving the screws may not be providing a tight fit. Try replacing the attaching screw or add a locking or plastic washer.

I hope I have been able to answer your question and I would love to hear more from you.

Do you have any questions?
Are there any topics you would like me to cover?

Although, I will continue to write articles about my experiences, I want to hear from you. Everyone has questions, I would love to hear yours and I love answering them. I also encourage you to leave comments or share additional information on any article on my site.

Bow Tuning – Advanced Tuning

So far in this series, we started by discussing the basic Olympic recurve bow setup. We covered what tools you require for bow tuning and to basically setup your bow. This included limb alignment, how to measure, installing the arrow rest, nocking point and setting up your basic center shot.

Now that your bow is basically setup, you have been practicing with it and have a fairly consistent arrow group it is time to do some advanced tuning of your bow. Remember that basic step-up and tuning can be done quickly to get you started however advanced tuning is a time consuming task through trial and error.  Proper shooting technique is always the first thing every archer should focus on. If you are still struggling with the basics then get your bow basically setup and work on consistency.  To avoid massive amounts of frustration, it is very important to focus on changing and tuning one thing at a time. Read my earlier blog about Consistency and Change.

Next we will focus on individual areas for you to tune such as nocking points, bowstring fit, centering, clearance, brace height, sight alignment, tiller, clicker and plunger adjustment. Since I already created several blogs about tuning specific components your bow, you should start by reviewing the following…

Sight : Following the arrow and adjusting your sights

Clicker : Adjusting and shooting with a Clicker.

Arrows and various tuning methods : Arrow Series – Part 8 – Fine Tuning and Numbering

Remember, bow tuning is an advanced technique and if you can I recommend you employ the knowledge and experience of a trained coach, since another pair of eyes can really help make the difference between a good tuning and perfection. In the next part of the series we will continue and take a deeper dive into the remaining areas of your bow that can be tuned. 

Shooting with a Clicker

Every competitive Olympic recurve archer uses a draw length checker or “clicker”. A clicker is a device that assists an archer to draw their bow consistently.  The clicker rides along the side of the arrow and produces a “clicking” sound after it passes over the point, hence the name “clicker”. By consistently measuring the draw length of the arrow, you get a consistent power off the bow and therefore a more consistent grouping of arrows resulting in better scores.

There is a lot of debate of when you should start to use a clicker. Anyone who wants to advance and develop smaller groups should start using a clicker as soon as possible. HOWEVER, since clickers take a lot of discipline, patience and practice, maturity is the key factor; age maturity and shooting maturity. If you are disciplined and maintaining consistent form, then you are ready for a clicker.

Recently, one of my readers asked:

I just wanted to ask, with regards to the form, if I should be expanding my chest during the draw (pulling your shoulders back towards the spine) in order to activate the back muscles to take the load rather than the arms.

Shooting a clicker is a relatively simple process however; it requires the use of back muscles to create something called back tension. By compressing the rhomboid major muscles (between the shoulder blades and spine) together, it will draw the arrow past the clicker for the shot when you are at full draw.

First, you need to determine the ideal location for your clicker. Have a friend mark where the tip of the arrow is at full draw. This will be the initial starting location for your clicker. There are tons of clickers on the market however there are two basic types of clickers; riser-mounted or sight-mounted. Depending where the initial starting location is measured it will help you determine the type you need.

Once you have mounted your clicker follow this shot process.

1. Nock the arrow, with the arrow under the clicker and on the arrow rest.
2. Raise the bow and draw towards your anchor point.
3. Continue to draw the arrow until the tip of the point is still just in contact with the clicker.
4. Aim and while still maintaining, squeeze your rhomboid major muscles together.
5. Once you hear the “click”, relax your fingers and finish the shot.

It is important that you are able to reach your anchor point at full draw. The clicker needs to be within the distance so your rhomboid major muscles can activate the shot. Remember, over the course of an entire day of shooting, your muscles weaken and you will have to work harder to draw the same amount, it may need to be adjusted to find the ideal location for entire day of shooting.

Important: Once you have determined your clicker location, leave it alone. Making any adjustments will affect all your sight marks, and they will need to be adjusted too.

If you have never used your rhomboid major muscles before this is going to take some time to master. Practice using your rhomboid major muscles with the following exercise.

With palms down and your forearms parallel to the floor, bring your fingertips together at chin level. Try squeezing your rhomboid major muscles together. You should witness your fingers spread apart about an inch. This is all the space you need to activate the clicker at full draw.

You can also check out this website for exercises to help develop strength in your rhomboid muscles.

The mastery of a clicker is essential for any competition archer. You will need to work on it regularly however once you master the process a clicker will become your best friend.

Follow the Arrow: Adjust your sights

Unless you are a traditionalist, one of the first things you will need to do as an archer is adjust your sight. Unless you are a compound shooter with the same setup for ever, you will need to make adjusts again and again. For recurve archers there are many reasons why you will need to make adjustments including…

Environmental Differences : Every location is different, wind, rain; check out my earlier blog about Weather Conditions here.

New Distances : As you develop and change categories, distances change. Junior women need to shoot 70M and junior men 90M, if you are not there yet, do not worry, you will be.

Growth : As you get older, your body changes, you get taller and stronger and your draw length changes, using a clicker can help with consistency, so check out my Clicker blog.

Equipment Changes : As you get stronger and you are required to reach longer distances you need to change equipment, such as higher poundage limbs. Eventually equipment wears outs and we all want the latest and greatest technology.

Archery Form Changes : As you develop as an archer, you will perform better as an archer and your archery form will get better.

For young recurve archers adjusting a sight is a frequent event and is actually quite easy, the hard part is resisting the temptation to adjust it after every shot. Remember that consistency is your ultimate goal, so track your arrows before making any adjustments. You can do this on paper or there is an awesome free application for your IPod Touch called Archery Score Free by Yakoob Ali.  Once you are warmed up begin to track your arrows and determine the centre of your arrows grouping and then move the sight accordingly. Remember, if your groups were good yesterday and are not today, evaluate your form first. Also, if you have one arrow consistently out of group, check the arrow for defects.

When you are ready to adjust your sight, apply this simple rule, “Follow the arrow” or in this case the centre of the group of arrows. If the centre of your arrow grouping is to the left, then move your sight towards the left or opposite if your group is to the right.  The same principle applies for the group’s height; move your sign up or down if the group is not centered.  By moving the sight towards the arrow, the trajectory of the bow is altered to better centre the arrows on the target.

Remember, consistent form is essential to archery, and before you start micro-adjusting be sure you are grouping consistently first. Otherwise, if you are always making changes to your sight you will never truly know if you will consistently hit the bulls-eye.

Clicker, Clicker, my Kingdom for a Clicker.

At some point, if you want to become a more competitive archer, you are going to need to incorporate a draw length check or “clicker” to your bow. A bow clicker is a device that assists an archer to draw their bow consistently.  The clicker rides along the side of the arrow and produces a “clicking” sound after it passes over the point, hence the name “clicker”. By consistently measuring the draw length of the arrow you get a consistent power off the bow and therefore a more consistent grouping of arrows resulting in better scores.

Clickers take a lot of discipline and practice however once mastered, it is a competitive archer’s best friend.

Clickers can be mounted on the riser itself or along the sight depending on the length of your arrows and your draw length. Riser mounted clickers can be adjusted a little however you need to cut the arrows to match. Younger archers who require longer arrows and have shorter draw lengths should use sight mounted clickers.

Cartel Doosung offers a variety of choices for clickers that are extremely affordable.  Check out their selection here.