Bow Tuning – Basic Setup continued

IMG_7304Now that your bow is together we need to make sure the arrow rest is installed correctly, install a nocking point and adjust the center-shot. It is my recommendation to always install the arrow rest before installing your nocking point. So, let’s start with the arrow rest.

Installing the Arrow Rest

There are a lot of types or arrows rests available on the market. Check out my earlier blog about the various types of arrow rests. For this blog, I will be focusing on the most commonly used one for Olympics style bows, the pressure/plunger rest.

The main purpose of the arrow rest is to hold the arrow in place until the arrow is shot. A  plunger style arrow rest is designed with a support arm just long enough to hold the arrow, with a slight inward angle to the bow, and it moves out of the way with the shot.  They should also be adjusted so that the support arm does not protrude beyond the outside of the arrow. This is to minimize contact with the arrow and minimize impact on the arrow flight. Lastly the arrow rest must be positioned so the plunger/pressure button is square to the center of the arrow.

arrow-rest-backhole

Olympic recurve bows come with a threaded hole for the plunger/pressure button and the arrow rest typically is installed and centered over the hole as the arrow rest and plunger work in conjunction with each other. Note, some risers have two holes and you should use the back one as a starting point which should be directly over the riser’s pivot point.

Pivot Point: The deepest part of the riser handle.

Alternatively, if your bow did not come with a threaded hole or you are using a traditional bow the arrow rest should be installed at the contact point of the arrow onto the rest directly above the “pivot point” of the bow. You may also want to investigate other types of arrow rests to match your style of bow.

Nock Pointing

Although some recurve archers use a tie-on nocking point, I recommend starting with a simple clamp-on type nock. Clamp-on style nocks are fairly easy to install and simply require your bow square and nocking pliers.

Nocking point: The location you attach your nock, it is usually measured 5mm (1/4”) above square from the center of the plunger and arrow rest.

measure-nockingAttach your bow square to the string so it is centered on the plunger ( or plunger hole) then measure up 5mm, attach a clamp-on nock, and secure it with nocking pliers. If your arrows are loose on your string, you can consider adding a nock serving for a better fit however once the nock is installed you can begin shooting.

Center-shot and the Plunger

For an Olympic archer the plunger (pressure button) is probably the best thing to attach to your bow for fine-tuning. The plunger can be adjusted to help match an archer’s release and counteract a lot of archer’s paradox. For a better understanding of arrow selection, center-shot and Archers Paradox check out my earlier blog.

To set your center-shot, set you plunger to the middle and install it in the threaded hole. Attach an arrow to the string, below the nock, and from behind the bow check to see if the tip is pointing slightly to the left (or right for left-handers).

center-shot

Although adjusting the plunger WILL require a trial and error approach, it is important to set the plunger to the middle position using the screw on the end. The amount of pressure setting for your plunger will depend on the archer, the limb poundage and your form. The best approach is to start with medium pressure and adjust accordingly after shooting a couple of arrows (Typically clockwise for more pressure and counter-clockwise for less).

Your bow should be basically setup and ready for you to focus on  developing consistent form. In upcoming blogs I will dive deeper into fine-tuning your bow.

Advertisements

Vision – Glasses, Contacts and Archery

Being an archer, competitive or recreational, does not require perfect 20/20 vision. E Perez asked…

I’m not sure if you’ve worn glasses before but if so, do you have any suggestions on archers who used glasses and are now switching to contacts? I’ve recently switched from glasses to contacts and my aiming is way off!

I can relate to this question, when I started shooting I had 20/20 vision, and around high school I needed glasses. I have not tried contacts yet, however it was an adjustment. Remember, the purpose of a corrective lens helps refract the light or images into in focus so you can see. Check out this website that explains how your vision works and how corrective lenses affect vision.

Wearing glasses or contacts can sometimes be a challenge for archers, since we actually stand to the side of the bow, not directly behind it. Therefore we are always viewing things on an angle, add the complexity of a corrective lens and it may be difficult to clearly focus on the target. It depends on the strength and thickness of the corrective lenses. I have a friend who can not shoot with her contacts on. The angle of the bow, combined with the angle of her contacts and she can not see her string alignment at all, which can affect your group.

Picking glasses out also presents a challenge because of the angle of the lenses and the thickness of the frames. My sister can not shoot with her prescription glasses because the frames are too large for the angle of the bow and she can not see her string alignment. If you need corrective lenses, it may take some trial and error experimenting to find out what works best for you.

I’ve recently switched from glasses to contacts and my aiming is way off!

If you are able to see the target and string alignment in focus, consider your arrow groupings.

Groups open up: Your brain could be simply catching up with your new perception, give it some time and practice. If the groups do not get better, then try shooting with your glasses on again and comparing the results.

Groups still tight; just off center: Move the sight. Even the smallest change can affect everything else, your vision is a large change.

Moved your sight; no change: Check your form, since many things can affect your your arrows including plucking the string.

Vision is important however not as important as good form. In fact, you may have read my earlier blog about legally blind South Korean archer, Im Dong-hyun, who broke the world record at the London 2012 Olympic Games. Im Dong-hyun has only about 20% vision in his right eye and only 10% in his left eye.

Your eyes can deceive you, don’t trust them – Obi-Wan Kenobi Star Wars

Your vision is important, however you may want to focus on making sure the shot “feels” the same every time, this is the key to success. For me, my coach still insists everyone warm-up with the following exercise to help us focus on feel not vision.

Close-Open-Close Warm-up 

  1. Close your eyes and draw your bow to full draw; focusing on your form. Try to make sure all your muscles and bones are in the same position with the same amount of pressure
  2. Quickly open your eyes to move the sight to the target
  3. Close your eyes and then shoot.

I hope I have provided some guidance and answered your question. If any other readers have experienced changes from moving to contacts from glasses, we would love to hear from you.

Arrows Series – Part 8: Fine Tuning and Numbering

Now that your center-shot is right, you’ll need to continue to fine-tune your bow periodically to change as you grow and develop as an archer. Start by labelling and numbering your arrows. Labelling your arrows with your name or initials is required for tournaments and sometimes is the only way you can distinguish your arrows from someone else’s; especially if they have the same nocks, shafts and fletchings.

Numbering is a good idea so you can track your arrows, if you have a single stray arrow. If the stray is consistent on every end and the number is the same, it may be that something is not right with that arrow.

Once you know your arrows and can track them, you can further tune your bow by adjusting various components such as the tiller, plunger, nock height etc… . You can perform some or all of these various tuning test to help tune your bow for maximum performance.

Paper Tuning Test: Tuning test involving setting up a piece of paper on a frame, stretching the paper taught, and shooting field-tipped arrows (not broadheads, which will affect the arrow flight) through it starting about 6 ft away.

Bare Shaft Planing Test : Tuning process were one shoots a bare arrow (shaft with no fletchings) for comparison with fletched arrows.

Walk-back Test: Tuning process where groups of arrows are shot at increasing distances to give a useful combined test of both centre-shot and button tension.

Check out these two very useful resources: Easton Tuning Guide and Tenzone’s Bow Tuning test documents: for instructions with these tests and many more.

As you develop as an archer you will need to make changes and tune your bow. Remember that making multiple adjustments at the same time can be hard to track and can be very confusing. It is important to only make one change at a time and test again.

This concludes the Arrow Series; Thanks and good shooting.

Arrows Series – Part 7: Center Shot and Archer’s Paradox

Now that you have determined the arrows you should use you need to fine-tune your bow to maximize your arrows consistency. Most people think that once you set up a plunger and a nocking point it is all good to go, however that is not the case. The center shot of your arrow is one of the most over looked things when setting up a bow.

The center shot is where the arrow rests on the bow when looking behind it.  When setting up your center shot the arrow needs to be completely behind the string. Most traditional bows do not have a cut-away in the riser and the arrow has to deflect around the handle with something called archer’s paradox.

Archer’s Paradox: The term was coined by Robert P. Elmer in the 1930s. The paradox refers to the phenomenon that in order to strike the center of the target, the arrow must be pointed slightly to the side of the target. Modern use of the term has caused the interpretation of it to be corrupted and the bending of the arrow is often considered incorrectly to be archer’s paradox.

In order to be accurate, an arrow must have the correct stiffness, or “spine”, to flex out of the way of the bow and return back to the correct path as it leaves the bow. Incorrect spine results in unpredictable contact between the arrow and the bow, therefore unpredictable forces on the arrow as it leaves the bow, and therefore reduced accuracy.[1] Additionally, if an archer shoots several arrows with different spine, even if they clear the bow they will be deflected on launch by different amounts and so will strike in different places. Competition archers therefore strive not only for arrows that have a spine within a suitable range for their bow, but also for highly consistent spine within sets of arrows. (Wikipedia)

For an Olympic archer, ideally your set up should be 100% behind the string. Some people actually require the arrow lean a little to the opposite side of your riser so that the arrow can get past the bow without hitting it. You can reduce the effects of “Archers Paradox” by adding spin to the arrow by fletching your vanes or feathers with an offset or helical. It is critical that the arrow must have the correct spine so it can bend around the bow, so the fletchings do not touch anything for consistent arrow flight.

Therefore, once again I stress, for proper safety and best performance, arrows need to match your entire bow setup.

Arrows Series – Part 6: Fletching and Indexing

Now that you have cut your arrows you need to fletch them. Fletchings are found at the back of the arrow, traditionally made from bird feathers and are used to stabilize the arrow by creating a small amount of drag.

Wikipedia: Fletching (also known as a flight) is the aerodynamic stabilization of arrows or darts with materials such as feathers, each piece of which is referred to as a fletch. The word is related to the French word “fleche”, meaning “arrow,” via Old French; the ultimate root is Frankish fliukka. A fletcher is a maker of arrows.

Nowadays, there are two types of fletchings, real or synthetic feathers and plastic vanes. Some target archers have them attached to the arrow with a slight twist to increase arrow spin because a spinning projectile is more stable and helps reduce the effects of Archer’s Paradox (We will discuss Archer’s Paradox in more detail in the Part 7 of the series).

The most conventional style of indexing is a three-feather fletching where feathers or vanes are mounted to the arrow, evenly distributed around the spine of the arrow. One feather, called the “cock”, is set at a right angle to the string and pointed at the archer and the other two fletchings on the riser side are angled up and down away from the bow. This is done so the fletchings/vanes will not contact the bow when the arrow is shot. For compound archers the cock feather’s indexing depends on the type of arrow rest.

Quick Tip: Choose a different colour for the “cock” feather. It is great reminder to always point it towards you and away from the riser for proper nocking of the arrow.

Fletching an arrow is a time consuming and tedious task to do accurately by hand. In modern times, most people use a fletching jig, especially to fletch arrows with a slight twist. Check out my earlier blog about fletching jigs.

It is important to understand that once an arrow is released it starts to bend and if the arrow is not correctly indexed the feathers or vanes will make contact with the riser. This will cause the arrow to react differently than expected, distort your feathers and possibly cause damage to you or your equipment.

Canada Captures the Bronze

Norbert Murphy captured the Bronze yesterday in the Men’s individual Compound -W1 division.

To reach the semi-finals, Norbert first defeated Shinichi Saito of Japan and Peter Kinik of Slovakia.  In the semi-final he faced Jeff Fabry of the United States, the eventual Gold Medalist. After Norbert lost 3-7 he moved into the Bronze medal match to face Osmo Kinnunen of Finland. Norbert shot extremely well tieing only a single end to take home the bronze medal.

Jeff Fabry of the United States went on to capture the Gold defeating David Drahoninsky  of Czech Republic in the Finals 6-2.

Congratulations!!!!

Shooting with a Clicker

Every competitive Olympic recurve archer uses a draw length checker or “clicker”. A clicker is a device that assists an archer to draw their bow consistently.  The clicker rides along the side of the arrow and produces a “clicking” sound after it passes over the point, hence the name “clicker”. By consistently measuring the draw length of the arrow, you get a consistent power off the bow and therefore a more consistent grouping of arrows resulting in better scores.

There is a lot of debate of when you should start to use a clicker. Anyone who wants to advance and develop smaller groups should start using a clicker as soon as possible. HOWEVER, since clickers take a lot of discipline, patience and practice, maturity is the key factor; age maturity and shooting maturity. If you are disciplined and maintaining consistent form, then you are ready for a clicker.

Recently, one of my readers asked:

I just wanted to ask, with regards to the form, if I should be expanding my chest during the draw (pulling your shoulders back towards the spine) in order to activate the back muscles to take the load rather than the arms.

Shooting a clicker is a relatively simple process however; it requires the use of back muscles to create something called back tension. By compressing the rhomboid major muscles (between the shoulder blades and spine) together, it will draw the arrow past the clicker for the shot when you are at full draw.

First, you need to determine the ideal location for your clicker. Have a friend mark where the tip of the arrow is at full draw. This will be the initial starting location for your clicker. There are tons of clickers on the market however there are two basic types of clickers; riser-mounted or sight-mounted. Depending where the initial starting location is measured it will help you determine the type you need.

Once you have mounted your clicker follow this shot process.

  1. Nock the arrow, with the arrow under the clicker and on the arrow rest.
  2. Raise the bow and draw towards your anchor point.
  3. Continue to draw the arrow until the tip of the point is still just in contact with the clicker.
  4. Aim and while still maintaining, squeeze your rhomboid major muscles together.
  5. Once you hear the “click”, relax your fingers and finish the shot.

It is important that you are able to reach your anchor point at full draw. The clicker needs to be within the distance so your rhomboid major muscles can activate the shot. Remember, over the course of an entire day of shooting, your muscles weaken and you will have to work harder to draw the same amount, it may need to be adjusted to find the ideal location for entire day of shooting.

Important: Once you have determined your clicker location, leave it alone. Making any adjustments will affect all your sight marks, and they will need to be adjusted too.

If you have never used your rhomboid major muscles before this is going to take some time to master. Practice using your rhomboid major muscles with the following exercise.

With palms down and your forearms parallel to the floor, bring your fingertips together at chin level. Try squeezing your rhomboid major muscles together. You should witness your fingers spread apart about an inch. This is all the space you need to activate the clicker at full draw.

You can also check out this website for exercises to help develop strength in your rhomboid muscles.

The mastery of a clicker is essential for any competition archer. You will need to work on it regularly however once you master the process a clicker will become your best friend.